Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
- 8. Fuel system
   - 8.1.1. Introduction
      8.1.2. A fuel tank
      8.1.3. The gauge of level of fuel
      8.1.4. The fuel pump
      8.1.5. The fuel filter
      8.1.6. The air filter
      8.1.7. A cross-section pipe of the air filter
      8.1.8. An inlet gas pipeline
      8.1.9. A cable of gas / the lever throttle заслонки (DB)
      8.1.10. A cable of management of gas (DB)
      8.1.11. A contour of fuel of the diesel engine
      8.1.12. Prestarting heating of diesel fuel
      8.1.13. The fuel thermostat
      8.1.14. The hydrovalve case
      8.1.15. A cable of gas / the lever throttle заслонки (ДД)
      8.1.16. A cable of management of gas (ДД)
   + 8.2. System of injection of petrol engines
   + 8.3. System of injection and a food of diesel engines
   + 8.4. System of release of the fulfilled gases
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes



canadian mail order pharmacies



8.1.9. A cable of gas / the lever throttle заслонки (DB)
THE GENERAL DATA

THE PETROL ENGINE

Regulation of a cable of gas (30)

PERFORMANCE ORDER
1. At the stopped engine and not pressed pedal of an accelerator between поводковой a spring (30/7) and a directing element (30/5) should be a backlash from 0,5 to 1,0 mm, otherwise establish it by means of the adjusting screw (30/3).
2. The cranked lever (32/5) should adjoin to the terminator of idling throttle заслонки, otherwise replace connecting draught (32/4). Connecting draught should be established very precisely. The microswitch in idling position should be pressed (will close).
3. The roller (32/8) without pressure should adjoin to the trailer terminator of the adjusting lever (32/7). Otherwise accordingly adjust connecting draught (32/4).
4. Adjust a cable of Boudena for installation of operating pressure (98). For this purpose turn the adjusting screw (98/2) until the edge of the shaking lever (32/2) will not be established at identical height with an edge кулисного the lever (32/6).
5. At the stopped engine charge to the partner to press an accelerator pedal against the stop the lever throttle заслонки, fix last in position of the maximum giving of fuel. In case of an automatic transmission do not put in action the switch of a pedal of an accelerator (S16/7).
6. Check up, whether throttle заслонки the lever of the platen adjoins to an emphasis of the lever throttle заслонки. An automatic transmission: otherwise accordingly turn the adjusting screw (30/3). A mechanical step transmission: adjust an emphasis of the lever throttle заслонки.

Regulation of an emphasis of the lever throttle заслонки in space for feet (only in case of a mechanical transmission)

PERFORMANCE ORDER
1. Deduce from gearing an emphasis of the lever throttle заслонки in space for feet, rotating it in a left-hand side, and extend a lock bolt a little.
2. Slowly squeeze out a pedal of an accelerator before position of the maximum giving of fuel until the lever throttle заслонки will not lie down on its emphasis.
3. In this position fix an emphasis of the lever throttle заслонки (38) by means of its rotation in the right party in internal space.
4. Release a pedal of an accelerator (24). Between поводковой a spring (30/7) and a directing element (30/5) should be a backlash from 0,5 to 1,0 mm, otherwise in internal space of the car spend adjustment by means of an adjusting nut (30/2).
5. Grease a cable of Boudena with anticorrosive greasing between a tip and a directing element (30/5).
6. If is available, check up adjustment темпомата.

Adjustment темпомата

PERFORMANCE ORDER
1. Unhook connecting draught (32/11) on one party of a spherical head.
2. The adjusting lever (32/7) should be in neutral position.
3. Turn an adjusting shaft (32/13) executive office темпомата (М16) in a direction of movement of an hour hand (in an arrow direction). In this case the executive office is in neutral position.
4. Turn an adjusting shaft (32/13) executive office темпомата (М16) in a direction of movement of an hour hand (in an arrow direction). In this case the executive office is in neutral position.
5. Then again hang connecting draught. Thus the executive office lever should be raised approximately on 1 mm from an emphasis of the lever throttle заслонки.
6. Otherwise adjust connecting draught. Wring out the spherical loose leaf. Ослабьте a counternut also screw in or unscrew the spherical loose leaf, again hardly tighten a counternut.