Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
- 8. Fuel system
   - 8.1.1. Introduction
      8.1.2. A fuel tank
      8.1.3. The gauge of level of fuel
      8.1.4. The fuel pump
      8.1.5. The fuel filter
      8.1.6. The air filter
      8.1.7. A cross-section pipe of the air filter
      8.1.8. An inlet gas pipeline
      8.1.9. A cable of gas / the lever throttle заслонки (DB)
      8.1.10. A cable of management of gas (DB)
      8.1.11. A contour of fuel of the diesel engine
      8.1.12. Prestarting heating of diesel fuel
      8.1.13. The fuel thermostat
      8.1.14. The hydrovalve case
      8.1.15. A cable of gas / the lever throttle заслонки (ДД)
      8.1.16. A cable of management of gas (ДД)
   + 8.2. System of injection of petrol engines
   + 8.3. System of injection and a food of diesel engines
   + 8.4. System of release of the fulfilled gases
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes







8.1.16. A cable of management of gas (ДД)
THE GENERAL DATA

THE DIESEL ENGINE


The prevention

The cable is very sensitive to bends and consequently at installation demands the accurate reference. The unique easy bend can lead to its later breakage at car operation. Therefore cables which have been earlier bent, it is not necessary to establish.


Removal

PERFORMANCE ORDER
1. The engine in volume of 2,0 l: unhook a cable of management of gas (230) on the adjusting lever (208). For this purpose squeeze out directing detail (240).
2. Engines in volume of 2,2/2,5 l: unhook a cable of management of gas on a spherical head of the directing lever.
3. Compress a plastic spring clip (228) and pull out тросовый a drive from a support (225).
4. Dismantle a casing under the instrument panel.
5. Unhook fastening тросового a drive (marksman) on the lever of a pedal of an accelerator (223). For this purpose unhook a returnable spring (235) and extend the holder (233/2) together with распорным a bolt.
6. Press from internal space of the car outside a cable of management of gas. Thus do not squeeze out the rubber plug.
7. Remove in the complete set a cable of management of gas.

Installation

PERFORMANCE ORDER
1. Grease a cable of management with gas between a directing element and a tip anticorrosive plastic greasing of type Mercedes-000 989 5110.
2. Instructions: at vehicles with an automatic transmission the cable of management of gas is established in its fastening together with a spring (marksman). Thanks to it the way of the lever of a pedal increases and possibility of deenergizing of the switch of a pedal of an accelerator is given.
3. Check up on damage or porosity the rubber plug (231), if necessary replace.
4. Stretch a cable of management of gas in internal space of the car and suspend on the accelerator lever. Pick up a returnable spring.
5. Mount a casing under the instrument panel.
6. Enter a cable of management of gas through an aperture in a support, press on a support and fix.
7. The engine in volume of 2,0 l: hang a cable of management of gas on the adjusting lever and fix it by means of a directing detail (240).
8. The engine in volume of 2,2/2,5 l: press a cable of management of gas on a spherical head of the directing lever.
9. Adjust a cable of management of gas.