Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
- 8. Fuel system
- 8.1.1. Introduction
8.1.2. A fuel tank
8.1.3. The gauge of level of fuel
8.1.4. The fuel pump
8.1.5. The fuel filter
8.1.6. The air filter
8.1.7. A cross-section pipe of the air filter
8.1.8. An inlet gas pipeline
8.1.9. A cable of gas / the lever throttle заслонки (DB)
8.1.10. A cable of management of gas (DB)
8.1.11. A contour of fuel of the diesel engine
8.1.12. Prestarting heating of diesel fuel
8.1.13. The fuel thermostat
8.1.14. The hydrovalve case
8.1.15. A cable of gas / the lever throttle заслонки (ДД)
8.1.16. A cable of management of gas (ДД)
+ 8.2. System of injection of petrol engines
+ 8.3. System of injection and a food of diesel engines
+ 8.4. System of release of the fulfilled gases
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes
|
The diesel engine in volume of 2,0 l
The diesel engine of 2,2/2,5 l
24. An accelerator pedal
31/1. The directing lever
32. A cable of management of gas
|
32/3. An adjusting bolt
38. An emphasis of the lever throttle заслонки |
PERFORMANCE ORDER |
Check up on ease of a course and damage the adjusting lever, connecting draught and a cable of management of gas. Replace the damaged details. |
|
Adjustment on an idling mode (an accelerator pedal (224) is not pressed)
PERFORMANCE ORDER |
1. Ослабьте шестигранный a bolt () on connecting draught (200) hydrovalves. |
2. Ослабьте a nut (204/1) on a spherical head of connecting draught (204). |
3. Until then rotate an adjusting nut while the roller (215) in кулисном the lever without pressure will lie down on a trailer emphasis.
The prevention After adjustment between a plate of a spring (226) and the spring (227) should not be a backlash.
|
4. Tighten a nut (204/1) on a spherical head of connecting draught. |
5. An automatic transmission: hang without a tension spherical подпятник a cable of management (211). For this purpose a management cable pull to notable resistance. Rotate a bolt (211/1) until тросовый a drive подвиснет without a tension. |
6. Directing lever (d) the hydrovalve rotate until he will lie down on the idling terminator. |
7. Stretch connecting draught (200) on the riveted party until the free wheeling will be established. |
8. Tighten a bolt with шестигранной a head (). |
|
Regulation of full gas (mechanical transmission)
PERFORMANCE ORDER |
1. Rotating to the left, uncouple an emphasis of the lever throttle заслонки (216) in space for feet. Slowly squeeze out a pedal of an accelerator (224) until the control lever will be directly reached an emphasis of the lever throttle заслонки by) (arrow) on the pump of atomizers. |
2. In this position, rotating to the right, fix an emphasis of the lever throttle заслонки (216) in internal space. |
|
Regulation of full gas (automatic transmission)
PERFORMANCE ORDER |
1. Squeeze out a pedal of an accelerator (224) against the stop without actuating of the switch of an accelerator (S16/7). |
2. Rotate the adjusting screw (232) until the control lever will be directly reached an emphasis throttle заслонки by) (arrow) on the fuel pump of atomizers. |
|
Regulation of a cable of management by gas
PERFORMANCE ORDER |
Check up on ease of a course and damage the adjusting lever and a cable of management of gas. The damaged details replace. |
|
Regulation in an idling mode (the accelerator pedal is not pressed)
PERFORMANCE ORDER |
|
Rotate an adjusting bolt until the directing lever without pressure will lie down on the course terminator (). |
|
Regulation of full opening throttle заслонки (a mechanical transmission)
PERFORMANCE ORDER |
|
1. Rotating to the left, uncouple an emphasis of the lever throttle заслонки (38) in space for feet and extend a persistent bolt a little. |
2. Slowly squeeze out an accelerator pedal until the directing lever will directly reach an emphasis of the lever throttle заслонки (b), limiting its maximum opening. |
3. Rotating to the right, fix in this position an emphasis of the lever throttle заслонки in internal space. |
|
|
|