Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
- 5. Cooling system
+ 5.2. A cooling liquid
5.3. Antifreeze for a radiator
5.4. A temperature regulator of a cooling liquid (thermostat)
5.5. Check of system of cooling
5.6. Hydraulic муфта the fan
5.7. The pump of system of liquid cooling
5.8. A radiator
5.9. A fan casing
5.10. Diagnostics of malfunctions of system of cooling
5.11. Diagnostics of malfunctions of system of indication of level of a liquid
5.12. An engine overheat
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes
|
THE 4-CYLINDER PETROL ENGINE
1. A nozzle рожкового a wrench
2. A Dinamometrichesky wrench
3. A countersupport at a pulley with a flat lock washer
3а. A countersupport at a pulley with the bolts having internal шестигранник
25. The fan |
25а. A bolt 6 х 14, 10 Н.м.
26. A sealing ring
26а. A nakidnaja nut
33. A pulley
33а. A flat lock washer
And – Untwisting
In – Screwing up |
Removal
PERFORMANCE ORDER |
1. Turn off рожковым a key накидную a nut, thus by means of a countersupport clamp a pulley of the pump for giving of a cooling liquid.
The prevention The nut has the left carving.
|
2. Extend hydraulic муфту together with the fan. |
3. Unscrew 3 fixing bolts and separate the fan from муфты. |
|
Installation
PERFORMANCE ORDER |
1. Connect муфту to the fan.
The prevention Correct assembly position of the fan is defined by means of the welded on edge.
|
2. Screw hydraulic муфту with the moment 10 Н.м. |
3. Insert hydraulic муфту together with the fan and screw with the moment in 40 Н.м. For this purpose it is required динамометрический a wrench with a nozzle рожкового a wrench.
The prevention The nut has the left carving.
|
|
THE 6-CYLINDER PETROL ENGINE
Removal
PERFORMANCE ORDER |
1. Remove a fan casing. |
2. Unscrew a bolt (3) on hydraulic муфте the fan. Thus keep a pulley from rotation in an opposite side by means of a self-made key on лыске a disk (6). |
3. Take the fan together with hydraulic муфтой. |
|
Installation
PERFORMANCE ORDER |
1. Thus insert the muftu-fan that welded on number of a detail was ahead from outside a radiator. |
2. Screw the muftu-fan with the moment 45 Н.м., thus keep a pulley from rotation in an opposite side. |
3. Establish a fan casing. |
|
THE DIESEL ENGINE IN VOLUME OF 2,0/2,2 L
Removal
PERFORMANCE ORDER |
1. Unscrew () накидную a nut (2а) a wrench (5), thus fix a pulley of the pump of system of liquid cooling by means of a countersupport (9).
The prevention The nut has the left carving.
|
2. Take together with the fan (1) hydraulic муфту (2). |
3. Unscrew three fixing bolts (3) and separate the fan from муфты. |
|
Installation
PERFORMANCE ORDER |
1. Insert муфту into the fan of system of cooling. By means of a ledge on a fan ring correct assembly position of the fan is defined. Marks "VORNE FRONT" specify in a movement direction. |
2. Screw hydraulic муфту the fan with the moment 10 Н.м. |
3. Insert муфту into the fan of system of cooling and together screw them on a shaft of the pump for giving of a cooling liquid with the moment 45 Н.м. For this purpose it is required динамометрический a key with a nozzle рожкового a key 36.
The prevention The nut has the left carving.
|
|
THE DIESEL ENGINE IN VOLUME OF 2,5 L
Removal
PERFORMANCE ORDER |
1. Remove a casing of the fan and lay it over the fan of system of cooling. |
2. Unscrew hydraulic муфту together with the fan of system of cooling, including a bolt with internal шестигранником. Thus keep a pulley by means of a countersupport. |
3. Extend upwards the fan (1) together with муфтой (2) and its casing. |
4. Unscrew the fan with four bolts (4) from hydraulic муфты. |
|
Installation
PERFORMANCE ORDER |
1. Insert hydraulic муфту into the fan of system of cooling and screw it with the moment 10 Н.м.
The prevention Marks "VORNE FRONT" specify in a movement direction.
|
2. Put together муфту with the fan of system of cooling and a fan casing. |
3. Screw the muftu-fan with the moment 45 Н.м., thus stop a pulley. |
4. Mount and adjust a fan casing. |
|
|
|