Mercedes S-class W202

1993-2000 of release

Repair and car operation

4.7.2. The diesel engine (2,0)

THE GENERAL DATA

The diesel engine in volume of 2,0 l

3. A stopper маслосливного apertures 6. An emphasis of the engine (type 201)

24. The shock-absorber of the engine (type 201)

Removal

PERFORMANCE ORDER

1. Remove the bottom cover of a motor compartment. 2. Remove the stabilizer of cross-section stability. 3. Disconnect the left longitudinal steering draught and the right shock-absorber of a steering. 4. Merge engine oil. 5. Disconnect a cable of weight of the battery (–). The prevention The anticreeping code of radio is thus erased. 6. Disconnect плюсовой wire X4 from a connection place to the bottom party of the car at the left and пложите from above the engine. 7. Disconnect a casing of the fan and put from above the fan. 8. Unscrew the gauge of number of turns (L3). 9. Disconnect a weight wire between a starter and a body (marksman). 10. Remove щтеккер the gauge of level of oil. 11. Disassemble intermediate steering сошку. 12. An automatic transmission: Separate маслопроводы in connecting details from маслошлангов, preliminary having clamped маслопроводы with the help шланговых clips. Connection elements close small plastic bags that the dirt did not get into them. 13. Pick up the engine a corresponding cable or a chain for a forward eye (marksman) and raise the crane. If is not present at the disposal of the crane, insert into a cable approaching шта нгу, slightly raise the engine and обоприте on supports. 14. Unscrew from below from a longeron a bolt with internal шестигранником for the left forward support of the engine. 15. Unscrew from a longeron from below a bolt with internal шестигранником the right forward support of the engine. 16. Raise the engine it is how much possible above. 17. The oil pallet with прифланцованной a lateral part: turn off a lateral part and remove together with a sealing lining. 18. Unscrew bolts of fastening (19) oil pallets and remove the oil pallet (45) forward, depending on a movement direction. If necessary slightly turn a cranked shaft. 19. Remove a sealing lining (45а), carefully clear sealing surfaces of the pallet and картера a cranked shaft.

Installation

PERFORMANCE ORDER

1. A negative wire of the storage battery. Establish the oil pallet with a new sealing lining, сориентировав it прилегание to a back surface of a transmission, and in regular intervals manually twirl fastening bolts. Then alternately screw up bolts with following moments: M 6 – 10 Н.м.; M 8 – 25 Н.м.; M 10 – 40 Н.м. The prevention In cars with an automatic transmission track, that the calibrated groove on an interface of the oil pallet has entered into the unloading plug of the motor block. 2. If occurred removal: establish a lateral part of the oil pallet with a new sealing lining and twirl with the moment 10 Н.м. 3. Lower the engine. 4. Establish bolts of fastening of a forward support of the engine and tighten with the moment 30 Н.м. 5. An automatic transmission: connect маслопроводы, remove шланговые clips. 6. Establish intermediate steering сошку. 7. Put on штеккер the gauge of level of oil. 8. Screw the gauge of number of turns. 9. Screw "a weight" cable between a starter and a body. 10. Establish and fix clips a fan casing. 11. Connect плюсовой a cable (Х4). 12. Hang the left longitudinal steering draught and the right shock-absorber of a steering. 13. Establish the stabilizer. 14. Establish the bottom cover of a motor compartment. 15. Fill in engine oil. 16. Connect a wire of "weight" of the battery. 17. Expose hours 18. Set an anticreeping code of radio. 19. Warm up the engine and check up tightness of the oil pallet. 20. An automatic transmission: check up oil level.