Mercedes S-class W202

1993-2000 of release

Repair and car operation


Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
- 4. Greasing system
   4.2. The engine oil specification
   4.3. A scope of oils / a viscosity class
   4.4. The oil expense
   4.5. A contour of circulation of oil (ДД)
   4.6. Oil редукционный the valve
   - 4.7. The oil pallet
      4.7.2. The diesel engine (2,0)
      4.7.3. The diesel engine (2,2 / 2,5)
   4.8. The indicator of level of oil
   4.9. The heat exchanger oil-/of a cooling liquid
   4.10. Diagnostics of malfunctions in a contour of circulation of oil
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes











4.7. The oil pallet

4.7.1. The petrol engine
THE GENERAL DATA

 
1. A radiator clip
2. A clip of the case of the fan
3. The fan case
4. A radiator
5. A covering of electroconducting of the engine
11. Bolts of a forward support of the engine 		12. Bolts of a back support of the engine
16. A cover
S43. Штеккер the gauge of level of oil
56. The oil pallet
56а. A sealing lining of the pallet

Bolts of fastening of the oil pallet

  
6. A bolt of M 6 х 20 9 mm
7. A bolt of M 6 х 35 9 mm
8. A bolt of M 6 х 85 9 mm		 9. A bolt of M 8 х 40 21 mm
10. A bolt of M 10 х 40 40 mm
56. The oil pallet

Removal
PERFORMANCE ORDER
1. Remove the bottom cover of a motor compartment.
2. Remove the stabilizer.
3. Lower engine oil.
4. Uncover (16).
5. Remove clips (2).
6. Raise the case of the fan and put on the fan.
7. Disconnect clips (1) from a radiator.
8. Ослабьте top маслопровод (marksman) on the pump of the amplifier of a steering also turn downwards.
9. Remove a cable tape for engine electroconducting.
10. Remove a covering of electroconducting of the engine from a dividing partition between units.
11. Disconnect a forward exhaust pipe from a final collector.
12. Unscrew a support of the holder of an exhaust pipe from a transmission.
13. Disconnect штеккер the gauge of level of oil.
14. Unscrew bolts of a forward support of the engine.
15. Unscrew bolts of fastening of a back support of the engine.
16. Hook on the engine for forward and back eyes.
17. Raise the engine as more as possible horizontally.
18. Unscrew fastening bolts (6/7/8/9/10) the oil pallet and remove the oil pallet (56) (fig. Bolts of fastening of the oil pallet see).
19. Carefully clear a sealing surface of the oil pallet and картера a cranked shaft.

Installation

PERFORMANCE ORDER
1. Establish the oil pallet with a new sealing lining, level it concerning a back surface прилегания to a check point and in regular intervals manually fix bolts. Then alternately twirl bolts with the ordered moment (fig. Bolts of fastening of the oil pallet see).
The prevention

If the oil pallet is not levelled concerning a transmission subsequently it will lead to noise.
2. Lower the engine.
3. Insert bolts of fastening of a forward support of the engine and screw up them manually.
4. Screw up bolts of a forward support of the engine with the moment 40 Н.м.
5. Put on штеккер the gauge of level of oil.
6. Attach a forward exhaust pipe to a final collector, a support of the holder of an exhaust pipe on a check point.
7. Establish a covering of electroconducting of the engine on a partition dividing units.
8. Fix electroconducting of the engine at the right wheel.
9. Turn маслопровод the pump of the amplifier of a steering upwards and fix.
10. Put on clips a radiator.
11. Establish the case of the fan and fix clips.
12. Establish a cover (16).
13. Establish the stabilizer.
14. Establish the bottom cover of a motor compartment.
15. Fill in engine oil.
16. Warm up the engine and check up tightness of the oil pallet.