Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   + 3.1.17. A klinovyj belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes











3.2.6. Натяжитель chains
THE GENERAL DATA

Chains arising at work noise can be caused lacks of functioning of the tension device. Disassemble and check up it. If necessary replace the tension device in the complete set.

Натяжитель chains (244) will screw on the right side in a head of the block of cylinders. Through an aperture in a head of the block of cylinders in натяжитель chains engine oil moves under pressure.


The chain stretches under action of force of a spring of compression (230) and pressure of oil in натяжителе. Pressure of a clip of a finger (233) on the tyre of management (215) is supported to constants by means of the return valve (227/228) and the valve of restriction of pressure (227/231), i.e. Does not depend on pressure of oil in the engine.

Removal
PERFORMANCE ORDER
Unscrew натяжитель chains for шестигранную a head (235) of a head of the block of cylinders.

The control

PERFORMANCE ORDER
1. Place натяжитель chains with a press finger in engine oil SAE 10. Oil level should be a little above a side шестигранной heads натяжителя. Press 7–10 times on press a finger a press.
2. After filling with oil натяжитель it should be compressed slowly, in regular intervals and with the big power effort. Otherwise replace it.

Installation


The prevention

Mount натяжитель chains only in the condition filled with oil.


PERFORMANCE ORDER
Establish натяжитель chains with use of a new sealing lining and tighten bolts of fastening with the moment 80 Н.м. Thus press the finger should adjoin to a ledge of a sled of a tension.