Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   + 3.1.17. A klinovyj belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes











3.2.4. The bottom cover of a motor compartment
THE GENERAL DATA

The prevention

At removal and installation do not damage a surface of a protective material of a cover.


Removal

PERFORMANCE ORDER
1. Raise the car.
2. Remove a forward covering (1), unscrew four bolts (arrow).
3. Remove a back covering (2), having unscrewed eight bolts of fastening. If there is a necessity, remove a lateral covering at the left and on the right, having turned off accordingly two bolts of fastening of a lateral covering to a longeron and one bolt of fastening to the bottom support of the cross-section lever of an independent suspension bracket.

Installation

PERFORMANCE ORDER
1. After dismantle establish a lateral covering and fix bolts.
2. Establish a back covering and fix bolts.
3. A forward covering establish so that the groove has in front entered into a partition of a lateral part of a covering (3).
4. Press a forward covering (1) upwards, thus the edge of a lateral part of a covering (3) should be from above coverings (1).
5. Tighten bolts of fastening of a forward covering.
6. Lower the car on the earth.