Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   + 3.1.17. A klinovyj belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes







3.2.18. The pulling device клинового a ridge belt Removal

PERFORMANCE ORDER
1. Remove hydraulic муфту the fan.

The prevention

The nakidnaja nut has the left carving.


2. Remove a fan casing.
3. Remove клиновой a ridge belt.
4. Wring out a screw-driver запорную a cover of a tension roller.
5. Unscrew a tension roller.
6. The engine in volume of 2,0 l: unscrew ременный a pulley of the pump of a cooling liquid.
7. Unscrew the shock-absorber of the device of a tension of a belt.
8. Unhook a stretching spring.
9. Unscrew конусный a bolt from the lever of a tension of a spring, preliminary having wrung out запорную a cover.
10. Remove the lever of a tension of a spring, track thus safety of a sealing ring and прокладочной washers.

Installation

PERFORMANCE ORDER
1. Establish the lever of a tension of a spring with a sealing ring and прокладочной a washer and tighten with the moment 100 Н.м.
The prevention

Clear a carving a wire brush before installation and cover with hermetic (the carving needs to be degreased).


2. Insert запорную a cover.
3. Hang a stretching spring.
4. Twirl the shock-absorber of the pulling device above with the moment 25 Н.м., and below with the moment 20 Н.м.
The prevention

If establish the new shock-absorber preliminary from it necessarily remove air. For this purpose in installation position some times move backwards-forward a piston rod.


5. The engine in volume of 2,0 l: twirl ременный a pulley of the pump of a cooling liquid with the moment 10 Н.м. (A bolt with internal шестигранником) or 15 Н.м. (торсионный a bolt).
6. Screw a tension roller with the moment 25 Н.м. (The engine 2,0) or 30 Н.м. (The engine 2,2/2,5). Insert запорную a cover.
7. Establish клиновой a ridge belt.
8. Establish a fan casing.
9. Establish hydraulic муфту the fan.