Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   - 3.1.8. A cover of a head of the block of cylinders
      3.1.8.2. The 6-cylinder engine
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   + 3.1.17. A klinovyj belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes







3.1.8.2. The 6-cylinder engine Removal


PERFORMANCE ORDER
1. Remove the air filter.
2. Disconnect a hose of ventilation of the engine (12) from the case of a head of the block of cylinders, preliminary having weakened шланговый a collar (11).
3. Disconnect a cover (7) sideways and extend upwards. Ослабьте bolts also uncover (9). Instructions: the wire of ignition represented in drawing does not correspond to type 202.
4. Ослабьте also remove all штеккеры spark plugs turn to the right-to the left. Put aside штеккеры spark plugs with ignition coils.
5. Unscrew bolts (14) cases of a head of the block of cylinders. Take the case of a head of the block of cylinders with a lateral sealing lining (2) and linings (3) for nests of spark plugs.

Installation

PERFORMANCE ORDER
1. Check up sealing linings on porosity and cracks. If one lining is damaged, it is necessary to replace simultaneously all linings.
2. At installation of a sealing lining special attention turn on correctness of landing into back dredging.
3. In regular intervals tighten bolts of the case of a head of the block of cylinders with the moment 10 Н.м.
4. Establish штеккеры spark plugs in proper order, for the installation explanatory on the case of a head of the block of cylinders the scheme is beaten out.
5. Fix spring clips and twirl cover bolts.
6. Put on a hose of ventilation of the engine and fix a collar.
7. Establish the air filter.
8. Warm up the engine to working temperature and check up tightness of a cover of a head of the block of cylinders, especially in the field of back dredging.