Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
3.1.2. Identification number
+ 3.1.3. The engine
3.1.4. Cars with the conditioner
3.1.5. The bottom cover of a motor compartment
3.1.6. Covers of cast apertures
3.1.7. Натяжитель chains
+ 3.1.8. A cover of a head of the block of cylinders
+ 3.1.9. A head of the block of cylinders
+ 3.1.10. Camshafts
3.1.11. Hydraulic тарельчатые pushers
3.1.12. Maslootrazhatelnye caps
3.1.13. Valves
3.1.14. Directing valves
3.1.15. Saddles of valves in a head of the block of cylinders
3.1.16. A compression
+ 3.1.17. A klinovyj belt
3.1.18. Diagnostics of malfunctions (DB)
3.1.19. Broad-brush observations
3.1.20. Repair work without engine dismantle
+ 3.1.21. Engine major repairs
+ 3.2. The diesel engine (ДД)
3.2.3. Cars with the conditioner
3.2.4. The bottom cover of a motor compartment
3.2.5. Covers of cast apertures
3.2.6. Натяжитель chains
+ 3.2.7. A camshaft
+ 3.2.8. A head of the block of cylinders
+ 3.2.9. Maslootrazhatelnye caps
3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
3.2.11. Hydraulic тарельчатые pushers
3.2.12. Valves
3.2.13. Directing valves
3.2.14. Saddles of valves in a head of the block of cylinders
3.2.15. A head of the block of cylinders and the motor block
3.2.16. A compression
3.2.17. Клиновой a ridge belt
3.2.18. The pulling device клинового a ridge belt
3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes
|
The prevention If натяжитель it is weakened on шестиграннике it should be removed, differently at screwing up the operating chain will be unduly tightened.
Removal
THE 4-CYLINDER ENGINE
PERFORMANCE ORDER |
|
1. Remove hydraulic муфту the fan. |
2. Uncover heads of the block of cylinders. |
3. Remove a fan casing. |
4. Establish the engine on 20 ° more low ВМТ ignitions of the first cylinder. For this purpose translate a transmission in position of idling and tighten a lay brake. Turn a cranked shaft by means of a wrench with nozzle SW27 at the central bolt of a belt pulley of a cranked shaft in a direction of rotation of the engine, i.e. Clockwise, before coincidence of marks. The length of a nozzle of a wrench should be more than 42 mm. |
|
5. Insure a final cam-shaft from turn. For this purpose enter a suitable core (Mercedes-N 111589011500) into an aperture of a flange of a cam-shaft (78) through an aperture in a cover of the bearing of a cam-shaft. If the chain in the same way fix an inlet cam-shaft acts in film. |
The prevention If do not insert fixing pin (arrow), adjust a cam-shaft substantive provision.
|
6. Close the generator a film or a rag. |
|
THE 6-CYLINDER ENGINE
PERFORMANCE ORDER |
7. Remove клиновой a ridge belt. |
8. If necessary ослабьте also remove the air pump from above натяжителя chains. |
|
ALL ENGINES
PERFORMANCE ORDER |
9. Ослабьте a screw stopper (1), having turned on one turn, using face key SW10. |
10. Unscrew натяжитель chains in a complex with a detail (14) and remove. |
11. Unscrew a screw stopper (1) with a sealing ring (5). Take a spring of compression (8) together with a pin (7). |
12. Push out back press a finger (10) with фиксаторной a spring (9). |
13. Details separately carefully clean fuel and check up on the further suitability to use (risks, a touch). The damaged details replace, in case of need in the complete set replace натяжитель chains. |
|
Installation
PERFORMANCE ORDER |
1. Fasten to the motor block the case натяжителя chains (14) with a new sealing ring (15). The moment of an inhaling for the 4-cylinder engine – 80 Н.м., for 6-cylinder – 50 Н.м. |
2. Collect details (7–10) as before their dismantling, and insert in mounted натяжитель chains. |
3. Twirl a screw stopper (1) with a new condensing ring (5) with the moment 40 Н.м., the spring is thus compressed. |
|
THE 4-CYLINDER ENGINE
The prevention Take stopping core from a cam-shaft flange.
PERFORMANCE ORDER |
4. Establish a cover of a head of the block of cylinders. |
5. Remove closing film from the generator. |
6. Establish hydraulic муфту the fan. |
7. Start the engine and check up tightness натяжителя chains. |
|
THE 6-CYLINDER ENGINE
PERFORMANCE ORDER |
4. Fix the air pump. |
5. Put on клиновой a ridge belt. |
6. Start the engine and check up tightness натяжителя chains. |
|
|
|