Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   - 3.1.3. The engine
      3.1.3.2. Installation
      3.1.3.3. Engine ventilation
      3.1.3.4. Functioning
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   + 3.1.17. A klinovyj belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes







3.1.3.2. Installation
PERFORMANCE ORDER
1. Check up engine support, hoses of a cooling liquid and маслошланги, and also топливопроводы on porosity, cracks, if necessary – replace.
2. Check up radial bearings коленвала and выжимной the coupling bearing on ease of rotation, and switching off lever – on ease of switching, if necessary – replace.
3. Check up a leading disk of coupling for a sufficient thickness and a condition of frictional overlays.
4. Forward and back bearings check up on porosity and absence of damages.
5. If the transmission was dismantled, fasten it to the engine and in common enter into a motor compartment.
6. Very cautiously lower the engine at installation in a motor compartment not to damage a leading shaft, coupling and a body.
7. Screw a transmission on an intermediate flange of the engine (the inhaling Moments see the table). Thus "a weight" wire screw at the left in the bottom of a transmission.
8. Insert and twirl manually bolts of fastening of forward support of the engine.
9. Back arms of the engine fasten fixing bolts with the moment 40 Н.м. And the moment 70 Н.м. For fixing nuts.
10. Tighten bolts of forward support of the engine with the moment 40 Н.м.
11. Insert карданный a shaft into a transmission.
12. An automatic transmission: put on штеккер starting blocking and the switch of a lantern of a backing and fix a plastic stopper. Connect an electric wire to magnetic valve Kickdown.
13. If the engine was dismantled without a transmission establish a starter.
14. Screw a cable of "weight" from a transmission on a body.
15. Hang switching levers on a transmission and fix clips. Check up adjustment.
16. Establish system of release of the fulfilled gases.
17. The conditioner: screw cooling compressor, mount клиновой a ridge belt.
18. Establish a radiator.
19. Put on all hoses of a cooling liquid and fix collars.
20. Establish the fan with hydraulic муфтой.
21. Establish the bottom covering of a motor compartment.
22. Lower the car on the earth.
23. Screw рециркуляционный a hose and a hose of a high pressure of the servo-driver of a steering. In cars with height adjustment screw in addition a hose of a high pressure and маслопровод for the two-planimetric pump. Remove air from the delivery oil pump of the two-planimetric pump.
24. Establish a gas cable.
25. Connect топливопроводы.
26. Put on all hoses of depression which go to the engine.
27. Establish a cross-section pipe of the air filter.
28. Establish a measuring instrument of weight of air if it was dismantled.
29. Check up oil level in the engine and a check point, in case of need add it.
30. Check up the antifreeze maintenance in a cooling liquid and add, if it is required.
31. Clean the loose leaf of the air filter, if necessary replace and insert into the filter.
32. At first connect плюсовой a battery wire (+), then "a weight" wire (–).
33. Fix накатной a nut and a rivet a covering on a forward wall of a body.
34. Finish the engine to working temperature, check up level of a cooling liquid and tightness of joining of hoses.
35. Close an engine cowl. For this purpose pull for the lock lever in the hinge of a cowl and slowly lower a cowl, it will not be felt yet противодавление springs and the lock lever will not be fixed.
36. Expose time for hours.
37. Set an anticreeping code for radio.
38. Take readings of memory of errors of the engine.

The inhaling moments

M 10 х 40
55 Н.м.
M 10 х 45
55 Н.м.
M 10 х 90
45 Н.м.