Mercedes S-class W202

1993-2000 of release

Repair and car operation


Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   - 3.1.17. A klinovyj belt
      3.1.17.2. The 6-cylinder engine
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes












3.1.17.2. The 6-cylinder engine Removal
PERFORMANCE ORDER
1. Extend fixing uvula (1) of a ring of a casing of the fan (2). Turn a covering in a direction of the beaten out arrow "open" and remove, turning крыльчатку the fan.
2. Ослабьте a bolt (16) on 1/4–1/2 turns. Turn a nut (5) to the left, thereby ослабьте a belt and remove it. In addition represented details: 13 – the index of adjustment, the marksman – the second division.

Installation
 1. A pulling roller
2. A remennyj pulley of a cranked shaft
3. The cooling compressor (conditioner)
5. The fan
7. The air pump
8. The generator
9. A directing roller
10. The pump of the amplifier of a steering
11. The pump of a cooling liquid
Length: 2337 mm or 2440 mm (with the conditioner)

PERFORMANCE ORDER
1. Check up a profile of belt pulleys and pulling device on absence of damages and pollution, in case of need clean or replace. Thus pay attention to the beaten out places of a support of the pulling device and лунки on belt pulleys.
2. Клиновые ridge belts with dirt adjournment between the edges weakened by edges, cracks, a fringe and the broken edges necessarily replace.
3. Impose клиновой a belt, since a pulling roller, according to sequence of numbering in drawing.
4. Establish the adjustment index on marks (1).
5. Turn a tension nut (5) to the right while the index of adjustment (13) will not coincide with marks (2).
6. Tighten a bolt (16) with the moment 75 Н.м.
7. Visually check landing of a belt to belt pulleys.
8. Establish a ring of a casing of the fan, turn and fix.