Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   - 3.1.17. A klinovyj belt
      3.1.17.2. The 6-cylinder engine
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes











3.1.17. A klinovyj belt

3.1.17.1. The 4-cylinder engine
THE GENERAL DATA

1. A pulling roller
2. A remennyj pulley of a cranked shaft
3. A remennyj pulley of the cooling compressor (only with the conditioner)
4. A remennyj pulley of the generator of a three-phase current
5. A remennyj pulley of the pump of the amplifier of a steering
6. A remennyj pulley of the pump of a cooling liquid
Lengths: 2040 mm and 2140 mm (with the conditioner)

1. A support
2. A pulling sleeve
3. A pulling roller
4. External bolt Е10

All additional units of the engine are put in action with the help клинового a ridge belt. It is wider, than usual клиновой a belt, and has on an inside many edges.

The automatic pulling device provides a uniform tension клинового a ridge belt for an appreciable length of time.

The belt needs to be checked within the limits of regular maintenance service on damages. Depending on the car equipment клиновые belts have various length.

Removal

PERFORMANCE ORDER
1. Remove hydraulic муфту the fan.
2. Spread a key with a nozzle for bolt Е10 on pulling roller and ослабьте a belt (11) turn clockwise.

Installation

PERFORMANCE ORDER
1. Check a profile of belt pulleys and pulling device on absence of damages and pollution, in case of need clean or replace. Thus pay attention to the beaten out installation sites of support of the device of a tension and лунки on belt pulleys.
2. Клиновые ridge belts with dirt adjournment between edges, cracks, a fringe and the broken edges necessarily replace.
3. Impose клиновой a belt, since a pulling roller, according to digital designations in drawing.
4. Release pulling roller (drawing see). Marks () should are only in working area (). If it does not occur, or the belt has inappropriate length, or the pulling device is faulty.
5. Visually check up landing of a belt to belt pulleys.
6. Establish hydraulic муфту the fan.