Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   + 3.1.17. A klinovyj belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes











3.1.14. Directing valves
THE GENERAL DATA

In the course of repair work on a head of the block of cylinders with not tight valves of processing or replacement of the valve and a saddle of the valve it is not enough. It is necessary to check up deterioration of directing valves.

It is especially important to check engines with long term of operation.

Worn out directing valves do not provide центричности a saddle of the valve and conduct to the raised expense of oil. If deterioration is too great, replace directing the valve (work for repair shop).
PERFORMANCE ORDER
1. Remove the valve.
2. Clean (1/2) directing the valve cylindrical brush (diameter about 20 mm).
3. Insert the valve from outside combustion chambers in directing and check up a backlash lateral moving of the gate backwards-forward. Thus it should not be felt an appreciable backlash. (1 – directing for the final valve, 2 – directing for the inlet valve, and – a spring lock ring.)
4. If necessary replace directing valves (work for repair shop).