Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. The engine
   3.1.4. Cars with the conditioner
   3.1.5. The bottom cover of a motor compartment
   3.1.6. Covers of cast apertures
   3.1.7. Натяжитель chains
   + 3.1.8. A cover of a head of the block of cylinders
   + 3.1.9. A head of the block of cylinders
   - 3.1.10. Camshafts
      3.1.10.1.2. The Control / substantive provision adjustment
      3.1.10.2. The 6-cylinder engine
   3.1.11. Hydraulic тарельчатые pushers
   3.1.12. Maslootrazhatelnye caps
   3.1.13. Valves
   3.1.14. Directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. A compression
   + 3.1.17. A klinovyj belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. Broad-brush observations
   3.1.20. Repair work without engine dismantle
   + 3.1.21. Engine major repairs
   + 3.2. The diesel engine (ДД)
   3.2.3. Cars with the conditioner
   3.2.4. The bottom cover of a motor compartment
   3.2.5. Covers of cast apertures
   3.2.6. Натяжитель chains
   + 3.2.7. A camshaft
   + 3.2.8. A head of the block of cylinders
   + 3.2.9. Maslootrazhatelnye caps
   3.2.10. A cover of a head of the block of cylinders (2,2/2,5)
   3.2.11. Hydraulic тарельчатые pushers
   3.2.12. Valves
   3.2.13. Directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. A head of the block of cylinders and the motor block
   3.2.16. A compression
   3.2.17. Клиновой a ridge belt
   3.2.18. The pulling device клинового a ridge belt
   3.2.19. Diagnostics of malfunctions (ДД)
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes







3.1.10.1.2. The Control / substantive provision adjustment
THE GENERAL DATA

Camshafts

1. A wrench (for turn of camshafts)
73. A management chain
75. A gear wheel of an inlet camshaft
76. A gear wheel of a final camshaft
77. A final camshaft
78. An inlet camshaft
79. A cover of the bearing of camshafts
79а. A fastening bolt

The control

PERFORMANCE ORDER
1. Establish the cylinder 1 on 20 after ВМТ. Instructions: in this position (20 after ВМТ) it is possible to turn camshafts at the removed managing director of a chain without contact of valves with the piston basis.
2. Uncover heads of the block of cylinders.
3. Fix camshafts. For this purpose enter fixing pins (01) through an aperture (arrow) in a cover of the bearing of camshafts 1 and 6 into an aperture of a flange of camshafts. If it is impossible to insert fixing pins, adjust substantive provisions of camshafts.

The prevention

For the engine in volume of 2,2 l turn a regulator of cam-shafts about a gear wheel of an inlet camshaft (75) in position "spat" (late) against the stop in a direction of rotation of a camshaft (marksman).



Adjustment

PERFORMANCE ORDER
1. The cylinder 1 costs on 20 after ВМТ ignitions and the cover of a head of the block of cylinders is removed.
2. Remove forward covers.
3. Remove натяжитель chains.
4. Unscrew a gear wheel of a final camshaft a wrench with nozzle Т40, holding a cam-shaft at шестигранника. Remove a camshaft gear wheel.
5. Remove an operating chain from a gear wheel of a final camshaft.
6. Turn camshafts a wrench until it will be possible to enter fixing pins.
7. Establish a chain wheel and impose a chain.
8. Establish натяжитель chains.
9. Once again check up a substantive provision of camshafts. If necessary repeat adjustment.
10. Establish forward covers of camshafts.
11. Establish a cover of a head of the block of cylinders.