Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
+ 13. A body
- 14. An electric equipment
14.1.2. Measuring devices
14.1.3. Technics of measurements
14.1.4. Electric equipment checks
14.1.5. A sound signal
14.1.6. Replacements of safety locks
+ 14.1.7. The storage battery
+ 14.1.8. The generator
+ 14.1.9. A starter
14.1.10. The traction relay
+ 14.1.11. Illumination system
14.1.12. Devices
14.1.13. The instrument panel
14.1.14. Lamps накаливания on the panel of devices
14.1.15. Light switch
14.1.16. A radio receiver
+ 14.1.17. The aerial
14.1.18. Dynamics
- 14.1.19. Rubber brushes of screen wipers
14.1.19.1. Diagnostics of malfunctions of brushes of screen wipers
14.1.20. Jets стеклоомывателя
14.1.21. Washing atomizers of headlights
14.1.22. A screen wiper and its engine
14.1.23. Protect the car
14.1.24. Anticreeping "immunodeficiency"
14.1.25. Why headlights grow dull
14.1.26. "Галогенки"
+ 14.2. Electroschemes
|
It is necessary to replace rubber brushes of a screen wiper at bad quality of clearing of glasses. In trade are offered as complete brushes of a screen wiper (a rubber brush with the holder), and separate rubber brushes of a screen wiper. If the rubber brush is replaced only, pay attention to that its holder has not been bent.
|
The rubber brush is entered in two metal fixing directing (1) which at removal should understand separately. |
Removal
The prevention At work on screen wipers Take the ignition key. At moving of the lever of a brush or the lever mechanism of a screen wiper, since position "1" ignition keys, automatics of return of brushes can join in a starting position. Т е. The screen wiper works in a single mode until it is in a starting position. There is a danger of a trauma!
PERFORMANCE ORDER |
1. Raise the lever of a brush of a screen wiper, without fixing it. |
|
2. Press downwards a plastic clip on a corrugated detail (1) and displace a screen wiper brush downwards (2) from a hook on the lever of a brush of a screen wiper. |
|
3. A narrow screw-driver (2) remove from the closed party back a rubber brush from both steel directing (2) and cautiously extend a rubber brush from the directing. |
4. Unhook a rubber brush (3) from collars (4) on a screen wiper. |
|
Installation
PERFORMANCE ORDER |
1. Freely lay a rubber brush not in fixing directing, and in screen wiper clips. |
|
2. Both directing the open profile party enter into a rubber brush so that flutes of the directing looked towards rubber and were fixed in groove ledges. The bend of the directing should look in a glass direction. |
3. Spring latches enter into a clamp flute if its preliminary forward end is mowed down by a file is easier and is greased with soap water (washing-up liquid). |
4. Grease a rubber brush on the closed party with soap water that it slid in collars is better. |
5. Both steel directing and a rubber brush clamp пассатижами and hang in collars of the screen wiper. |
6. Насаживайте a screen wiper brush so that it was between both directing pins on the screen wiper lever.
The prevention If the new brush of a screen wiper is established, press downwards plastic clips on corrugated details.
|
7. Push a screen wiper brush in hooks of its lever, clamp plastic clips and by that fix a screen wiper brush. |
8. Press the lever of a brush of a screen wiper. Thus pay attention to that the rubber brush everywhere adjoined to glass. |
9. Include a screen wiper. The clearing sector should be cleared easily.
The prevention The rubber sponge of a brush of a screen wiper at change of a direction of movement should be bent to (overturn). If it does not occur, cautiously bend the lever of a brush of a screen wiper so that its end settled down in parallel glass.
|
|
|
|