Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
- 13. A body
   13.2. A forward door
   13.3. A back door
   13.4. The handle of a forward door
   13.5. The handle of a back door
   13.6. A door-lock
   13.7. An internal covering of doors
   13.8. Forward стеклоподъемник
   13.9. Glass of a forward window
   13.10. Back стеклоподъемник
   13.11. Glass of a forward door
   13.12. The engine стеклоподъемника
   13.13. Perchatochnyj boxing
   13.14. A sheeting of the handle of a gear change
   13.15. A forward ashtray
   13.16. The average console
   13.17. The panel of service of heating
   13.18. An internal covering of the A-rack
   13.19. An internal covering of the S-rack
   13.20. A forward seat
   13.21. A back seat
   + 13.22. The central lock
   13.23. The external mirror / has flown down mirrors
   13.24. A covering under the instrument panel
   13.25. A forward bumper
   13.26. A back bumper
   13.27. An internal wing of the car
   13.28. A car wing
   13.29. A lattice of a radiator / emblem Mercedes
   13.30. Draught of a cowl of the engine
   13.31. A covering under a windscreen
   13.32. The device of giving of air for salon heating
   13.33. A catchment basin
   13.34. A paint and varnish covering
   13.35. Metal corrosion
   13.36. An automake-up
   13.37. What creaks?
   13.38. The hatch
+ 14. An electric equipment
+ 14.2. Electroschemes











13.7. An internal covering of doors
THE GENERAL DATA

Door of the driver

1. The handle стеклоподъемника
2. The lock socket
3. Deepening for the handle
4. A covering
5. An internal covering of a door
Instructions: on back doors it is necessary to spend work соответсвующим in the image

Removal

PERFORMANCE ORDER
1. Unscrew the socket of the lock (2) screw-driver and remove it.
2. Completely lower glass of a door by means of the handle.
3. Remove the handle стеклоподъемника for what a small screw-driver press a lock hook on a covering. Lower a covering downwards in a direction of an arrow and remove.
4. Remove the handle from an axis, remove распорную a washer.
5. Бленду (3) for door actuating from within disconnect fingers or a screw-driver from an internal covering of a door and remove.
6. Unscrew the screw (6) on the mechanism of management of a door from within.
7. Wring out a covering (4) under an armrest in a door pocket and unscrew the screw with crosswise шлицем on a head.
8. An internal covering of a door кругообразно slightly disconnect from a door tin.
9. A door covering wring out from a door tin from the bottom party and sideways wide шпателем or a screw-driver, thus disconnect spring clips. To begin with the bottom party of a covering.
The prevention

Lay a material not to scratch a varnish.


10. Open a stopper (7) mechanisms of actuating of a door from within and disconnect the mechanism (8). At "электрически an adjustable seat of the driver" instead of the mechanism flexible draught is built in, disconnect it.
11. Disconnect штеккер wires from a door covering.
12. Pull an internal door covering upwards over the button of blocking of a door and take from a door tin.

Installation

PERFORMANCE ORDER
1. Before assemblage track correct installation герметизирующей films. Small damages of a film stick with a sticky tape, at the big cracks replace a film.
The prevention

At factory the holder of fastening of an armrest приклепывается only after film installation. At film replacement cut out this area and stick внахлестку or condense with a gluing tape.


2. Put on a wire socket.
3. Insert the mechanism of actuating of a door from within and fix it.
4. Replace the damaged spring clips. Establish an internal covering from above over the button of blocking of a door, enter into the tyre for a sealant and simultaneously with spring clips in apertures in a door tin.
5. Press fists an internal covering of a door in the field of spring clips.
6. Twist the screw with crosswise шлицем below an armrest. Impose a covering.
7. Fasten management of a door from within two screws. Impose a handle cover.

8. A washer of a backlash (3) handles стеклоподъемника establish in the big diameter to a door covering.
9. Spread the handle on an axis. At an open window the handle should be directed obliquely forward upwards.
10. Pull from below a cover (1) over the handle (2), thus track, that the cover head has entered into a flute on a handle axis. Advance a covering forward so, fixing hooks (arrow) will not enter yet into gearing.
11. Raise glass upwards by means of the handle.
12. Insert a covering for a door-lock from above and from below fix the screw.