Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
+ 12. Brake system
- 13. A body
13.2. A forward door
13.3. A back door
13.4. The handle of a forward door
13.5. The handle of a back door
13.6. A door-lock
13.7. An internal covering of doors
13.8. Forward стеклоподъемник
13.9. Glass of a forward window
13.10. Back стеклоподъемник
13.11. Glass of a forward door
13.12. The engine стеклоподъемника
13.13. Perchatochnyj boxing
13.14. A sheeting of the handle of a gear change
13.15. A forward ashtray
13.16. The average console
13.17. The panel of service of heating
13.18. An internal covering of the A-rack
13.19. An internal covering of the S-rack
13.20. A forward seat
13.21. A back seat
+ 13.22. The central lock
13.23. The external mirror / has flown down mirrors
13.24. A covering under the instrument panel
13.25. A forward bumper
13.26. A back bumper
13.27. An internal wing of the car
13.28. A car wing
13.29. A lattice of a radiator / emblem Mercedes
13.30. Draught of a cowl of the engine
13.31. A covering under a windscreen
13.32. The device of giving of air for salon heating
13.33. A catchment basin
13.34. A paint and varnish covering
13.35. Metal corrosion
13.36. An automake-up
13.37. What creaks?
13.38. The hatch
+ 14. An electric equipment
+ 14.2. Electroschemes
|
Door of the driver
1. A covering
2. A sealing lining
3. A-rack bolts |
4. A protective sleeve
5. An aligning bolt |
Removal
| PERFORMANCE ORDER |
| 1. Completely lower a window of a door of the driver. |
| 2. Wring out a covering (1) and by means of the special tool turn to the right an internal tetrahedron disconnect blocking tetrahedral штекерного door connections. |
| 3. Remove a sealing lining. |
|
4. Unscrew a bolt (13) door brakes (10). 14 - an internal tetrahedron in a bolt head. |
| 5. Note position of door hinges concerning their surface прилегания, for example, lead round them чертилкой or откернуйте above and below. Adjustment of this door at installation As a result is not required. |
| 6. Unscrew four шарнирных a bolt (3) and together with the assistant slightly disconnect a door from a door pillar. |
 |
7. Disconnect a protective sleeve (4) from a rack of a door and take штеккерное connection (11). |
| 8. Remove a door, trying not to damage a varnish covering. |
|
Installation
| PERFORMANCE ORDER |
| 1. Insert штеккерное connection (11) and close a stopper, having turned outside. |
| 2. Fix spring clips a protective sleeve (4). |
| 3. Establish a door and slightly fix fastening bolts. |
| 4. So adjust door position that hinges have coincided with the put marks. |
| 5. Mount a covering (1). |
| 6. Twirl with the moment 25 Н.м. A bolt (13) fastenings of a door brake to a door pillar. |
| 7. Attach a covering (1 and 2). |
| 8. Adjust a door, twirl aligning bolt (5) with the moment 25 Н.м. And bolts of hinges (3) with the moment 35 Н.м. |
|
Adjustment
If the door is insufficiently driven after dismantling, it should be adjusted.
| PERFORMANCE ORDER |
 |
1. Turn off a protective cover (7) door-locks (8). |
| 2. Adjustment is made by easing шарнирных bolts and door removing. Hinges have apertures more than diameter of bolts so the hinge can be moved. |
 |
3. For adjustment of the sizes of joints ослабьте шарнирные bolts (6) on a body, without unscrewing them. The size of a joint adjust door movement. So adjust a door that in relation to the details of a body located close the backlash was parallel also identical size. |
| 4. Door adjustment to a body contour: if the door in the closed condition insufficiently densely applies on a body, ослабьте шарнирные bolts (3) and (5) on a door and accordingly move a door. The back door should enter a maximum on 1 mm in front inside further, than a forward door. |
| 5. A protective cover of a door-lock (7) screw up until then that it could be shifted easy blows of a rubber hammer. |
| 6. Adjust a protective cover of a door-lock in the bottom area of a door. Close a door and level, as a result of it position of a protective cover of a door-lock is levelled also. Then cautiously open a door and tighten screws of a protective cover. That it is better to supervise moving, before easing of screws outline a felt-tip pen position of a protective cover. Tighten screws of fastening of a protective cover of the lock with the moment 30 Н.м. |
| 7. Check up correct прилегание sealing linings of a door to a car roof edge. If the door in the closed position is located faultlessly, tighten шарнирные bolts. |
|
|
|
