Mercedes S-class W202

1993-2000 of release

Repair and car operation



Mercedes W202
+ 1.2. The general data
+ 2. Maintenance service
+ 3. Engines
+ 4. Greasing system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. Ignition system
+ 8. Fuel system
+ 9. Transmission
+ 10. A running gear
+ 11. A steering
- 12. Brake system
   12.2. Antiblocking system – ABS
   12.3. The additional equipment – system ASR
   12.4. Specifications of brake system
   12.5. Overlays of lobbies brake колодок
   + 12.6. Overlays of back disk brakes
   12.7. A support
   12.8. A forward brake disk
   12.9. A back brake disk
   12.10. A brake liquid
   12.11. Removal of air from brake system
   12.12. Brake pipelines / hoses
   12.13. Replacement of brake highways
   12.14. Brake колодки a lay brake
   12.15. Adjustment of a lay brake
   12.16. The stoplight switch
   12.17. Diagnostics of malfunctions of brakes
   + 12.18. Wheels and tyres
+ 13. A body
+ 14. An electric equipment
+ 14.2. Electroschemes







12.14. Brake колодки a lay brake Removal

PERFORMANCE ORDER
1. Remove a back brake disk.
2. Remove a back seat.
3. Remove a protective guard of the equalizer of length of a cable under a back seat.
4. Pull the automatic equalizer of length of a cable (12). For this purpose turn a wrench with internal шестигранником a crank (g) approximately on 1/2 turns to the right and simultaneously advance it back in longitudinal шлице, while the crank will not be fixed in the spring case () in a spring clip (d), (е – the equalizer lever, f – the intermediate lever, 93 – a safety pin, 94 – оттяжная a spring.)
5. Turn a flange of a shaft of a back axis (68) so that the aperture with a carving was over a spring (107).
6. A clamping spring (107) slightly compress tool Mercedes-040, turn on 90 (1/4 turns) and unhook. The auxiliary tool can be made also independently: on one party of a bar of the corresponding diameter weld the T-shaped handle, and on other party cut шлиц depth about 4 mm and width about 2,5 mm.
7. In the same way remove clamping springs of others brake колодок.
8. Disconnect оттяжную a spring (111) from brake колодок by means of the tool (041) or screw-drivers.
9. Disconnect from each other both brake колодки (112) and remove through a flange of a shaft of a back axis. Note assembly position of the adjusting adaptation. The adjusting wheel is directed forward.
10. Disconnect оттяжную a spring (112) from brake колодок and Take the adjusting adaptation (104) to (106).
11. Push out the plug (114) of распорного the lock (109) and remove распорный the lock from a cable (86).

Installation

PERFORMANCE ORDER
1. All basic surfaces and sliding surfaces распорного the lock grease with a thin layer of high-temperature greasing, for example, Liqui Moly LM-36, Molykote-Paste-U or G-Rapid.
2. Fix a brake cable (86) with a finger (114) on распорном the lock (109). Then press on распорный the lock in a direction of a protective ring (102).
3. Unscrew one of other detail of the adjusting adaptation. Grease with high-temperature paste a carving of a press detail, and also a cylindrical part of an adjusting wheel.
4. Screw in a press detail (104) in an adjusting castor (105) and insert into a press sleeve (106). Thus completely screw in a press detail.
5. The adjusting adaptation establish between both brake колодками so that the press detail (104) specified in a movement direction.
6. Connect to brake колодкам оттяжную a spring (112).
7. Move apart brake колодки, establish on a flange of a shaft of a back axis and pass in распорный the lock.
8. Insert a press spring by means of the auxiliary tool in brake колодку, slightly having compressed, turn on 90 <M ^> about and, as a result, insert into a protective ring. In summary check up correctness of landing of a spring.
9. Insert a press spring for another brake колодки.
10. An ottjazhnuju spring a small ear insert into a lobby brake колодку. The big ear (arrow) by means of a screw-driver insert into another brake колодку.
11. Establish a back brake disk.
12. Ослабьте the automatic equalizer of length of a cable. For this purpose raise a screw-driver a spring clip then the equalizer of length will be established automatically.
13. Establish a protective cover of the equalizer of length of a cable and twirl bolts.
14. Establish a back seat.
15. Adjust a lay brake.